The SYC-30 PP Duct Air Cooler is a high-capacity evaporative cooling unit built for large factories, warehouses, workshops, production floors, logistics facilities, and commercial spaces. The SYC-30 PP (PRM) delivers 30,000 CMH airflow through an axial fan while using a 3 kW motor. Its 180–200 Pa air pressure also allows the unit to work with properly designed duct systems.

For industrial sites in Qatar, ducted cooling offers a practical way to carry fresh air into specific working zones rather than placing several small coolers around the facility.

Nassguard supplies the SYC-30 PP for cooling requirements across Qatar and Doha, including industrial and logistics locations around Doha, Al Rayyan, Al Wakrah, Birkat Al Awamer, Mesaieed, Ras Laffan, Al Khor, and Umm Salal.

What is the SYC-30 PP Duct Air Cooler?

The SYC-30 PP Duct Air Cooler is an industrial evaporative cooler that lowers the temperature of incoming fresh air through water evaporation and then distributes that air through an outlet or duct network.

During operation, hot outside air passes through wet cooling media. Some of the water evaporates and absorbs heat from the passing air. An axial fan then pushes the resulting cooler air toward the outlet. Suitable ductwork can carry this air to production lines, workstations, storage zones, or other occupied sections.

This approach differs from conventional refrigerated air conditioning. Evaporative cooling continually introduces outside air instead of relying mainly on recirculated indoor air. Synergy recommends duct air coolers for large spaces such as factories, warehouses, workshops, showrooms, and commercial buildings.

Key Features of SYC-30 PP

• 30,000 CMH Airflow: High-volume air delivery suits large industrial and commercial spaces.
• 3 kW Motor: The motor powers the axial fan for continuous industrial airflow.
• Axial Fan: This fan configuration moves a substantial volume of air through the cooler.
• Top/Down Discharge: Two discharge arrangements provide flexibility when planning the installation.
• 180–200 Pa Air Pressure: The available pressure supports appropriate ducted air distribution.
• Large Cooling Coverage: The manufacturer lists approximately 250–300 m² for the PRM model.
• Industrial Electrical Supply: The unit operates on 3-phase 415V at 50 Hz.
• Manual/Remote Control: Users can operate the system through manual or remote-controller configurations.
• 40–45 L Water Tank: The integrated tank supplies water to the evaporative cooling section.
• 900 × 900 mm Outlet: The large outlet provides a practical connection point for high-volume air distribution.

Uses of SYC-30 PP

• Factory Cooling: Supplies fresh cooled air to production and assembly areas.
• Warehouse Cooling: Improves airflow around storage, packing, and material-handling zones.
• Workshop Cooling: Helps manage heat in fabrication, mechanical, and maintenance workshops.
• Production Cooling: Directs fresh air toward machinery and active work zones.
• Logistics Facilities: Supports cooling around loading, sorting, storage, and dispatch sections.
• Maintenance Areas: Provides continuous air movement around suitable repair and service locations.
• Commercial Spaces: Serves large commercial buildings where evaporative cooling suits the conditions.
• Ducted Air Distribution: Carries fresh cooled air to selected zones without placing a cooler in every area.

Applications Across Qatar and Doha

• Doha: Warehouses, workshops, and commercial facilities can use the SYC-30 PP to distribute fresh cooled air across large working areas.
• Doha Industrial Area: Factories, garages, and fabrication workshops can use the cooler for ducted airflow around production and maintenance zones.
• Al Rayyan: Warehouses and workshops can use the unit to improve air circulation across suitable industrial and commercial spaces.
• Al Wakrah: Industrial facilities can use the cooler for fresh-air movement and evaporative cooling in large working areas.
• Birkat Al Awamer: Warehouses and logistics facilities can use ducted cooling across storage, packing, and operational zones.
• Aba Saleel: Logistics centres and industrial facilities can use the unit for high-volume air distribution through warehouses and workshops.
• Mesaieed: Industrial plants can use the cooler in suitable production, maintenance, workshop, and storage areas.
• Ras Laffan: Industrial support facilities can use the unit to improve airflow around suitable workshops and maintenance buildings.
• Al Khor: Warehouses, workshops, and service facilities can use the cooler for workplace cooling and fresh-air circulation.
• Umm Salal: Storage facilities and workshops can use the SYC-30 PP for suitable ducted cooling applications.
• Lusail: Commercial and service facilities can use the unit where site conditions favour evaporative cooling.

Synergy specifically identifies factories, warehouses, workshops, service centres, and commercial spaces among applications for industrial and ducted air cooling systems.

Technical Specification

How Does the SYC-30 PP Work?

Water keeps the cooling media wet while the axial fan draws hot outside air through it. As water evaporates, it absorbs heat and lowers the temperature of the passing air. The fan then moves the cooler fresh air through the outlet.

Once connected to suitable ductwork, the system can direct air toward selected workstations or larger operational zones. Synergy notes that ducted systems can distribute cooled air across multiple areas while keeping the main cooling unit outside or on a rooftop.

Proper ventilation matters. The facility needs a route for warm indoor air to leave as fresh air enters. Temperature, relative humidity, heat load, occupancy, duct resistance, and building layout will all influence real-world performance.

Why Choose SYC-30 PP from Nassguard?

The SYC-30 PP offers 30,000 CMH airflow without relying on a conventional compressor-based cooling cycle. This makes it worth considering for large spaces where fresh-air circulation matters. Its large 900 × 900 mm outlet supports duct connection, while top/down discharge gives installers flexibility when planning the layout. The 180–200 Pa pressure range also supports suitable air-distribution arrangements.

Nassguard supplies industrial cooling equipment for projects across Qatar and Doha, including requirements for factories, workshops, warehouses, logistics operations, and commercial facilities.

Standards, Certifications and Compliance

The exact certifications of the supplied SYC-30 PP should be confirmed from its current manufacturer documentation. Relevant standards and regulatory references may include:

• IEC 60335 – Safety of Household and Similar Electrical Appliances
  
• ISO 9001 – Quality Management Systems
  
• CE Marking Requirements
  
• RoHS – Restriction of Hazardous Substances
  

These are relevant reference standards, not proof that every SYC-30 PP unit carries each certification. Confirm the manufacturer’s current certificates and declarations before making project-specific compliance claims.

Frequently Asked Questions

1. What is the SYC-30 PP Duct Air Cooler?
It is an industrial evaporative cooler that supplies fresh cooled air directly or through suitable ductwork.

2. What is the airflow of the SYC-30 PP?
The SYC-30 PP (PRM) has a published airflow of 30,000 CMH.

3. What area can the SYC-30 PP cool?
The manufacturer lists approximately 250–300 m² for the PRM version, although actual coverage varies with site conditions.

4. What power supply does the cooler require?
The PRM model uses 3-phase 415V, 50 Hz power with a 3 kW rating.

5. Can the SYC-30 PP connect to ductwork?
Yes, the duct cooler range supports ducted distribution, and this model has a 900 × 900 mm outlet.

6. Where can this cooler be used?
It suits appropriate factories, warehouses, workshops, production areas, logistics facilities, service centres, and large commercial spaces.

7. Is the SYC-30 PP available in Qatar?
Nassguard supplies industrial cooling solutions for customer and project requirements across Qatar and Doha.

Conclusion

The SYC-30 PP Duct Air Cooler provides a practical fresh-air cooling solution for large workplaces. The PRM version combines 30,000 CMH airflow, 3 kW power, an axial fan, 180–200 Pa air pressure, and stated coverage of 250–300 m².

Factories can direct air toward production zones, while warehouses can serve packing and material-handling areas through planned ductwork. Workshops, logistics centres, and suitable commercial facilities can use the same principle to improve fresh-air movement without filling valuable floor space with multiple portable units.

Nassguard supplies the SYC-30 PP for industrial and commercial cooling requirements across Doha and Qatar.